This is an old revision of the document!
LeisureCAN is a CAN-Bus system designed for the leisure vehicle industry - campervans, boats, caravans, …
It allows manufacturers to control all electrical and electronical components of the leisure side of the vehicle through a single CAN Bus. Any component can be switched from anywhere on the bus system, and any measurement taken can be displayed or used anywhere on the bus.
CAN (Control Area Network) technology was designed for the automotive industry in the 1990s. Nowadays, pretty much every new car has a CAN bus system that controls the engine, temperature, lights, indicators, etc. through a single bus system. They are very reliable (if electronics fail, it's usually not the bus itself, but individual components), and have been manufactured in the millions. That means the individual components are cheap, ubiquitous and reliable.
LeisureCAN is based on a peer-to-peer network. Every component connected to the bus is able to receive messages from any other component, and can send messages to all other components. The failure of a single component has no effect on the others, and there is no single point of failure.
The peer-to-peer model means that each component decides on its own what it wants to do with the information it receives. Each component can subscribe to events. As an example, a set of lights in the dining area can subscribe to a switch. When the switch is operated, a signal is transmitted onto the bus telling all components that the switch is now on. The component that the dining area lights are connected to reads the signal, figures out that it is subscribed to the signal, and turns the dining area lights on.
The same set of lights can have multiple subscriptions, e.g. a panic switch next to the bed can turn the same lights on in blinking mode when operated.
Components can also react to measurements, e.g. if the inside temperature gets too low, the heating can turn on automatically. At the same time, a switch could turn on the heating overriding the temperature reading, etc.
To sum it up, it's up to each individual component to decide what it wants to do with the messages received from the bus.
Security is provided through the WiFi networks own security, e.g. WEP password protection.
The main component is the bus itself, which consists of a 4 wire twisted pair shielded cable that runs along the length of the vehicle. The maximum bus length is 40 m, so the bus can easily be run along both sides, criss-cross, or in whatever layout is best. The bus cable is run through junction boxes into which the components are plugged. The cable, boxes and plugs are all IP68 compliant, e.g. the whole system is waterproof.
LeisureCAN units are plugged into the bus wherever needed in the vehicle. These units have a combination of switch inputs, analogue inputs (e.g. measuring inputs), relay outputs, and measuring gauge outputs. They can be bought or self made according to the needs of the customer. Most units will have a combination of switch inputs and relay outputs. As an example, a unit that is placed close to the dining area will have relay outputs to turn lights on and off, operate a fan, and receive switch inputs from a bank of switches.
When the units are installed, the subscriptions can be set up, e.g. the user can configure freely how the components react to each other.
A subscription is when a device reacts to the change from another device. So far, there are 6 subscription types, and they are as follows:
|Subscription Type||Short Name||Functionality|
|0||Normal Switch||If the subscribed unit receives a change from 0 to 1, it will switch on; if it receives a change from 1 to 0, it will switch off|
|1||Reverse Switch||If the subscribed unit receives a change from 0 to 1, it will switch off; if it receives a change from 1 to 0, it will switch on|
|2||Blink||If the subscribed unit receives a change from 0 to 1, it will start “blinking” the output relay at a set frequency (up to the implementor). The blinking will stop when a change from 1 to 0 is received.|
|3||push button||A push button subscription will switch on as soon as it receives a change from 0 to 1, but it will ignore the following change from 1 to 0. The next change from 0 to 1 will switch the subscriber off again.|
|4||Measuring Data||A measuring data output port will listen to a measuring data feed, that will supply an absolute measurement together with a unit marker. When configuring a measuring output port, the unit will get a minimal and maximal value set. It will now calculate the percentage of the measurement received in respect to the known minimal and maximal value, and calculate a percentage that the received measurement represents. It will then set the output voltage between 0 and 5 Volt on the port according to the received percentage. This can be used to drive stepper motor gauge outputs.|
|5||Any change switches||This is useful when for example a set of lights can be switched from multiple locations, e.g. different access routes leading to the same space. Each entry to the space has an on/off switch, and the relay driving the lights has a subscription to all of the switches. Any change on any of the switches will lead to a switch of the lights, no matter if the switch that changed switched from on to off or from off to on - pretty much like your traditional house electrics set-up for hallways.|
The huge advantage of a LeisureCAN system is that it's freely configurable, and the configuration can be changed at any time. If the user wants to add a new component (e.g. a new switch), he/she can just do that, and then configure which device reacts to the switch. In the same manner, a new device can be connected to the relay output of a LeisureCAN unit, and then be configured to be switched on by a set of events on the bus, e.g. a switch that's operated, …
Once the bus cable and a pair of power cables are fitted throughout the vehicle, new components can be added with a minimal amount of wiring required. Just hook up the new component to the power cable, and connect it to a relay output of the nearest LeisureCAN unit, and you are ready to go.
You could argue that a traditional copper cable wiring to each component is more reliable, but you have to take into account that you have a lot more connectors, cables, etc. running through your vehicle. All those provide additional points of failure.
I have been working in the car industry for over 2 decades, and when I started out in 1982, there were very little electronics in cars, especially the ones we mostly worked on. Electrical faults were rife, mostly contact problems, and they provided a constant source of annoyance for drivers.
Since the introduction of CAN bus systems in cars, the problems have shifted to individual components, which are now far more abundant. There are hundreds of sensors in a modern car, and huge amounts of actuators, valves, etc. that control the engine, brakes, steering, heating, air conditioning, etc. If we still had traditional cabling without a bus for those, we would see a lot more failures than we see with a neat central bus system that minimises cabling and connectors.
In my book, a complex electrical system with a CAN Bus is more reliable than a complex electrical system with traditional wiring. The most reliable system is of course a minimal system with minimal wiring and minimal functionality, but that might not be to everyone's taste …